Vanguard Cellular Data Modem & IP Router Series User Manual 001-7200-100 Revision 0; June 2011 USATUSATCORP.COMContact USATCORP.COM for m
9 Table 2 - Vanguard Accessories Vanguard Accessories ACC-ANTN-RBD 4” Rubber Duck Antenna ACC-ANTN-MAG 3” Mag Mount Antenna ACC-PWSP-ML2 110 V
10 1.6 EXTERNAL CONNECTORS This section describes the external connectors for the Vanguard modem. Figure 4 shows the front panel connections for
11 Table 3 describes these connections. Figure 4 Front Panel Standard Models Figure 5 Front Panel Mobile Models with GPS and WiFi Figure 6 Re
12 Table 3 – External Connectors Panel Indicator Connection Description COM RS-232 Serial to IP conversion use ANT SMA Primary RF Antenna AUX (Figur
13 antenna, with an average gain >-5dBi, if using the GPS functionality. If both RX diversity and GPS are required, install a Cellular/GPS combo
14 2 GETTING STARTED 2.1 PACKAGE CONTENTS Vanguard Modem Power Cable Information Card 2.2 DEVICE CONNECTIONS 1. (GSM Users) Insert the
15 Figure 8 LAN Configuration Screens 2.4 CELLULAR CONNECTIONS Before you begin, you will need an active Cellular account with the carrier of your
16 3 VANGUARD WEB INTERFACE Start your web browser and enter 192.168.1.50 in the address bar. A login screen should appear. Enter the User Name:
17 Figure 11: Vanguard CDMA Unit Status Window
18 Figure 12: Vanguard GSM Unit Status
Vanguard Cellular Data Modem & IP Router Series User Manual 001-7200-100 Revision 0; June 2011
19 LAN IP Displays LAN side static IP information for this device (the modem). Note: Once this IP address has been changed and saved, the browse
20 PPP IP Address Displays the current IP address of the Modem on the cellular network. This address, if public, should be reachable. 10.X.X.X su
21 Service Type Determines the type of network your device has connected to; GPRS, EDGE, UMTS, HSDPA, CDMA 1xRTT, EVDO Rev0 or RevA. ESN The
22 Figure 13: Vanguard CDMA Unit Status – Basic Settings Unit ID ID This identification number serves to distinguish this unit from other units
23 Change the Disable PIN setting from Yes (shown in Figure 14) to NO. Enter your carrier provided PIN into the Current PIN field. Click SAVE to acc
24 Figure 16 SIM Settings for PIN Required At this point the user has 3 attempts to enter the correct PIN. If the correct PIN is not entered after
25 3.3 PROVISIONING (CDMA MODELS ONLY) When a CDMA modem is powered up for the first time, most of the provisioning information is blank or has inf
26 If the auto-provisioning fails, and OMA-DM manual provisioning fails, and your outside the Sprint network, follow the manual-entry activation
27 The Electronic Serial Number is only applicable for the CDMA product line, carrier specific (Alltel, Verizon, Sprint, etc). This number is used
28 Click the Write MDN/MSID button when the required information has been entered. Enable/Disable OMA-DM Activation This section will only be dis
Copyright Notice ©2011 CalAmp. All Rights Reserved. CalAmp reserves the right to modify the equipment, its specification or this manual without pr
29 Figure 20: Vanguard CDMA Provisioning – Advanced Settings Profile Settings Profile Enable This field indicates if the profile is enabled. It
30 MN-HA SPI This parameter should be set to the MN-HA SPI setting supplied by the provider. This is a numeric setting. HA Secret This param
31 Figure 21: Vanguard CDMA Cell Connection – Dial Settings Figure 22: Vanguard GSM Cell Connection – Dial Settings
32 Dial Settings Auto Connect When set to Enable, will allow the modem to automatically dial the connection when the modem is powered. When set
33 Figure 23: Vanguard Cell Connection – System Monitor Periodic Reset Timer Periodic Reset Type Sets the Periodic Modem Reset timer to an Inter
34 Destination Address User may enter an accessible IP address or URL that will respond to a ping command. Secondary Address User may enter
35 The number of corrupted TCP and UDP packets received by the modem that were meant to be transmitted on the cell network. Tx Packets Dropped
36 The username used when setting up the account. Used to login to the Dynamic DNS service. User Password The password associated with the us
37 Figure 25: Vanguard LAN Settings Window
38 LAN Settings Ethernet IP Address This sets the IP address of this device and is the address used to access the configuration pages. If the IP
3 Revision History 2011 June Initial Release
39 DHCP end range DHCP server ending IP address. The maximum usable number is 253 DHCP Lease Time Sets the duration, in seconds, the connec
40 Enable or disable RADIUS authentication for webpage access Server IP Address The IP address of the RADIUS server Server Port The port of
41 Figure 26: Vanguard LAN Settings – MAC Filtering MAC Filtering MAC Filtering Radio button selection to Enable/Disable MAC filtering Allow
42 Figure 27: Vanguard Router – Port Forwarding DMZ Support DMZ is a host on the internal network that has all ports exposed, except those ports f
43 Port Forwarding Radio button selection to Enable/Disable. Select Enable to allow the modem to use the Port Forwarding routes described in the
44 Figure 28: Vanguard Router – Static Routes Static Routes Route Name Sets the alphanumeric identifier of the static route in the Static Route
45 3.7.1 PPTP The Point-to-Point Tunneling Protocol (PPTP) is a method for implementing virtual private networks (VPN). Figure 29: Vanguard VPN
46 Username The username required by the VPN server Password The password, associated with the username, required by the VPN server PPTP Serv
47 Figure 30: Vanguard VPN – IPSec IPsec Support IPsec Selecting Enable will launch the IPsec process and start all enabled tunnels. Selecting D
48 NAT Mode Determines how packets are addressed. Selecting Bypass will allow packets coming from Local Subnet addresses through the NAT firewa
4 Table of Contents 1 Product Overview ...
49 Phase 2 Encryption Use AES-128, AES-256 or 3DES encryption. Phase 2 Authentication Use MD5 or SHA1 hashing. Phase 2 Lifetime How long
50 Figure 31: Vanguard VPN – GRE GRE Tunnel Configuration Local IP Address The local IP address associated with the tunnel Remote IP Address
51 Figure 32: Vanguard Serial – External Serial External Serial Port Configuration Serial Port When enabled, the external serial port PAD functi
52 Baud Rate Sets the baud rate of the serial port. Settings may range from 300 to 115,200 bits per second. The default baud rate is 115,200 bps
53 DCD The DCD parameter determines how the modem controls the state of the Carrier Detect circuit and the amber DCD LED on the front panel. The
54 New Client: If a different client attempts to connect, it will be successful and the current client will be forcibly disconnected, without any wa
55 Time in seconds between keep alive cycles. A keep alive cycle will consist of one or more keep alive probes separated by the keep alive interval.
56 Remote IP Address Sets the IP address of the device using the PAD functionality Remote Port Sets the port number used by the remote device
57 Figure 34: Vanguard Diagnosics – SNMP SNMP Configuration SNMP Selecting Enable will allow the SNMP functionality. Selecting Disable will shut
58 SNMP v3 User Name The user name for secure access to the Management Information Bases (MIBs) observing v3 standard Password The correspond
5 3.10.1 Status ...
59 Version Displays the modem firmware version currently loaded in the unit Kernel Date Displays the date of the operating system kernel th
60 Figure 36: Vanguard I/O Settings – Status Device Input Status Main Voltage Displays current voltage applied to the unit, in Volts Modem T
61 Displays the status of the specified output as open or closed 3.10.2 SETTINGS Status Monitoring is provided via NMEA-based protocol. The Vanguard
62 Unit ID The Unit Name to be included in the NMEA message payload. Source Identification The Unit's IP address that will be included
63 Figure 38: Vanguard I/O Settings – Labels 3.11 FIRMWARE UPDATE When newer versions of the modem firmware become available, the user can downloa
64 Figure 39: Vanguard Firmware Update Current Firmware Information Version Displays the modem firmware version currently loaded in the unit.
65 Upload Button After selecting the firmware configuration filename above, press the Upload button to begin the configuration loading process.
66 4 SERVICE AND SUPPORT Product Warranty, RMA and Contact Information CalAmp guarantees that every Vanguard Modem will be free from physical defec
APPENDIX A – ABBREVIATIONS Abbreviation Description APN Access Point Name CSD Circuit Switched Data CTS Clear to Send DCD Data Carrier Detect D
APPENDIX B – WARRANTY STATEMENT CalAmp warrants to the original purchaser for use ("Buyer") that data telemetry products manufactured by D
6 1 PRODUCT OVERVIEW The Vanguard Series from CalAmp is the ideal solution for a wide range of cellular data network serial and Ethernet connectivi
7 TCP/IP Packet assembler and dis-assembler for serial connected devices Inbound IP termination with Static IP Modem Domain Names with Dyna
8 1.4 MECHANICAL SPECIFICATIONS The following section describes in detail the exterior dimensions of the 882 GSM Series modems and how to utilize t
Commentaires sur ces manuels